Maytag Bravos Washer Stuck On Sensing

The Maytag Bravos washer is a popular household appliance known for its efficiency and reliability. However, like any machine, it can encounter issues from time to time. One common problem that users may encounter is when the washer gets stuck on the “Sensing” cycle. In this article, we will explore the potential causes and troubleshooting steps to resolve this issue.

Understanding the “Sensing” Cycle


Several factors can cause the Maytag Bravos washer to become stuck on the “Sensing” cycle:

  1. Load Imbalance: The washer may be struggling to balance a heavy or uneven load. This can cause the machine to remain in the “Sensing” phase indefinitely.
  2. Water Supply Issues: If there’s an insufficient water supply or a problem with the water inlet valves, the washer may not be able to fill the drum properly, leading to a prolonged “Sensing” phase.
  3. Drainage Problems: If the washer can’t drain water from a previous cycle, it may not start a new one. This could be due to a clogged drain hose or a malfunctioning drain pump.
  4. Faulty Sensors: Sometimes, the issue might be with the sensors themselves. If they can’t accurately detect the load size or water level, it can cause the washer to stay in the “Sensing” phase.

Troubleshooting Steps

Now that we’ve identified the potential causes, let’s look at the steps you can take to resolve the issue:

  1. Check Load Balance:

    • Open the washer and redistribute the load evenly if it appears uneven.
    • For heavy items like blankets or comforters, try adding a few more items to balance the load.
  2. Inspect Water Supply:

    • Ensure that the water supply valves connected to the washer are fully open.
    • Check for kinks or clogs in the water inlet hoses. Replace them if necessary.
  3. Examine Drainage:

    • Verify that the drain hose is not kinked, clogged, or obstructed in any way.
    • Make sure the drain hose is positioned correctly, allowing water to flow freely into the drain.
  4. Restart the Cycle:

    • Press the “Cancel” button on the washer’s control panel to stop the current cycle.
    • Select a new cycle and start the washer again to see if it progresses beyond the “Sensing” stage.
  5. Check for Error Codes:

    • The washer might display an error code that can help pinpoint the issue. Refer to the user manual for instructions on how to interpret these codes.
  6. Reset the Washer:

    • Unplug the washer from the power outlet for a few minutes and then plug it back in. This can sometimes reset the control board and resolve minor issues.
  7. Contact Customer Support:

    • If none of the above steps work, it may be necessary to contact Maytag customer support or a qualified technician for further diagnosis and repair.
  1. Run a Calibration Cycle:

    • Some Maytag Bravos washers have a calibration cycle that can help the machine adapt to your specific water conditions and load types. Consult your user manual to see if your washer has this feature and how to initiate it.
  2. Inspect the Lid Lock:

    • The washer may not proceed past the “Sensing” cycle if the lid is not properly locked. Check if the lid lock mechanism is functioning correctly. If it’s damaged or malfunctioning, it may need to be replaced.
  3. Check for Overloading:

    • Overloading the washer can lead to the machine getting stuck in the “Sensing” phase. Be mindful of the recommended load capacity for your specific model and avoid exceeding it.
  4. Clean the Washer:

    • Over time, detergent residue, lint, and debris can accumulate in the washer’s drum and sensors, affecting its performance. Consider running a washer cleaning cycle or cleaning the drum and sensors manually.
  5. Inspect the Pressure Switch Hose:

    • The pressure switch hose is responsible for detecting the water level in the washer. If it’s damaged, disconnected, or clogged, it can prevent the washer from progressing. Check this hose for any issues and ensure it’s properly connected.
  6. Check for Software Updates:

    • Some washing machines can receive firmware updates to address performance issues. Check the manufacturer’s website or contact customer support to inquire about any available updates for your Maytag Bravos washer.
  7. Use the Right Detergent:

    • Using excessive or the wrong type of detergent can lead to excessive suds, which may interfere with the sensing process. Always use HE (High-Efficiency) detergent, and follow the manufacturer’s guidelines for detergent quantity.
  8. Regular Maintenance:

    • To prevent future issues, perform regular maintenance tasks such as cleaning the lint filter (if applicable), inspecting hoses for wear, and ensuring all connections are secure.

Common Symptoms

SymptomDescriptionPossible CausesSolutionsAdditional Notes
Washer Stuck on SensingWasher gets stuck on the sensing cycle.1. Faulty lid switch1. Replace the lid switch– Check for loose wires
2. Malfunctioning control2. Reset the control board– Ensure proper power supply
board3. Check for debris in the tub– Run a diagnostic test
3. Water supply issues4. Verify water supply connections
4. Sensor problems5. Clean or replace sensors

Troubleshooting Steps

StepDescriptionInstructionsAdditional Notes
1. Check Lid SwitchEnsure the lid switch is functioning correctly.– Open the washer’s lid.– A faulty lid switch can cause issues.
– Look for any visible damage or debris.
– Replace the switch if necessary.
2. Control Board ResetReset the control board to resolve glitches.– Unplug the washer from the power source.– This can often clear minor issues.
– Wait for a few minutes.
– Plug it back in and try the washer.
3. Tub InspectionCheck for any debris or objects in the tub.– Open the washer’s lid.– Foreign objects can disrupt sensing.
– Inspect the tub for foreign objects.
– Remove any debris or objects found.
4. Water Supply CheckEnsure there’s adequate water supply.– Verify water connections are secure.– Low water supply can affect sensing.
– Check water pressure and flow.
5. Sensor MaintenanceClean or replace sensors if necessary.– Refer to the user manual for guidance.– Dirty or faulty sensors can cause issues.

Error Codes

Error CodeDescriptionPossible Solutions
LF (Long Fill)Indicates a low water flow problem.1. Check water supply.
2. Clean inlet valve screens.
3. Replace faulty inlet valve.
4. Verify water pressure.
UL (Unbalanced Load)Indicates an unbalanced load.1. Stop the cycle.
2. Rearrange the load evenly.
3. Restart the cycle.
F5 E1Indicates a lid switch error.1. Inspect and reset the lid switch.
2. Replace the lid switch if faulty.
3. Check wiring connections.

Sensor Types

Sensor TypeFunctionLocation
Water Level SensorMeasures the water level in the tub.Usually near the bottom of tub.
Lid Switch SensorDetects whether the lid is open or closed.Located near the lid hinge.
Load Balance SensorDetermines if the load is evenly distributed.Positioned under the tub.

Professional Help

SituationWhen to Seek Professional Help
None of the above solutionsIf none of the troubleshooting steps
work and the issue persists.or DIY fixes resolve the problem.
Error codes persistIf specific error codes continue to appear
despite attempted fixes.even after addressing them.


Resolving the issue of a Maytag Bravos washer getting stuck on the “Sensing” cycle often involves a combination of simple troubleshooting steps. By carefully examining load balance, water supply, drainage, and other potential causes, you can usually identify and fix the problem. If you’re uncertain or the issue persists, reaching out to customer support or a qualified technician is a prudent next step to ensure the washer is operating optimally. Remember that regular maintenance and following manufacturer guidelines for usage can help prevent such issues in the future.


Maytag Bravos Washer Stuck On Sensing

Leave a Comment