Intelligent Single Door Controller
The Avigilon™ Access Control Manager (ACM)™ system supports open field hardware from Mercury Security allowing organizations to leverage investments in non-proprietary field hardware, with retrofit programs available for industry standard door hardware and card readers, including contact/contactless smart card, proximity, magnetic stripe and barcode.
The AC-MER-CONT-1DR is a powerful, intelligent controller solution for managing one or two on-board readers (expandable to 17 readers) with the Access Control Manager system from Avigilon.
Based on the Mercury Security EP1501, the ACMER-CONT-1DR communicates with ACM via its on-board PoE capable Ethernet port. The AC-MERCONT-1DR includes two inputs, two outputs and two reader ports and easily expands I/O and readers by simply adding input, output and reader interface modules. Easy installation with Power over Ethernet (PoE) makes this a top choice for a single controlled opening controller with ACM.
The Access Control Manager system and Mercury Security open field hardware provide the ultimate platform to complete the Avigilon end-to-end security solution.
KEY FEATURES
- PoE capable intelligent network controller
- Single-door interface that can expand to 17 reader doors
- Suitable for in/out reader applications
- Network ready
- Decentralizes system intelligence
- Triple gang footprint
- Provides full local processing
- Interfaces with a wide array of reader technologies including Wiegand, clock
- and data, magnetic stripe and keypads
- Support for up to eight device addresses through the on board RS-485
- communication port
- Support for the AC-MER-CON-MR50, AC-MER-CON-MR52, AC-MER-CONMR16IN and the AC-MER-CON-MR16OUT
- Support for the AC-MER-CON-MR51E over Ethernet
Specifications
| TECHNICAL SPECIFICATIONS | |
| Power Input | PoE Power Input 12.95W, compliant to IEEE 802.3af or 12 V DC ±10%, 200 mA minimum, 900 mA maximum power supply. Note: For UL installations, PoE powered devices shall not be used, power for these devices must be provided by an UL 294 listed power limited source (12 V DC). |
| Power Output | 12 V DC @ 650mA including reader and AUX output |
| Reader Interface | Powered by PoE (12 V DC +/-10%) or local power supply (12 V DC). (PTC limited 150mA max) |
| Inputs | Two unsupervised/supervised, Programmable End of Line resistors, 1k/1k ohm, 1 %, ¼ watt standard |
| Outputs | Two relays Form C, 2A @ 30 V DC, resistive |
| Reader Ports | Reader port 1: TTL compatible, F/2F or 2-wire RS-485 Reader port 2: TTL compatible or F/2F |
| Keypad | Multiplexed with card data |
| LED | TTL compatible , high > 3 V, low < 0.5 V, 5 mA source/sink maximum |
| Buzzer | Open collector, 12 V DC open circuit maximum, 40 mA sink maximum |
| Dimensions (W x L X H) | 140mm x 70mm x 24mm; 5.5” x 2.75” x 0.96” without bracket 140mm x 92mm x 34mm; 5.5” x 3.63” x 1.33” with bracket |
| Temperature | Operating: 0° C to 70° C (32° F to 158° F) Storage: -55° C to 85° C (-67° F to 185° F) |
| Humidity | 5 – 95% Relative humidity (non-condensing) |
| TECHNICAL FEATURES | |
| Connectivity | Primary Port: 10/100 Ethernet |
| Door Control | One physical barrier can be controlled using single or paired readers.
Two reader ports — Mag, Wiegand, or RS-485 (RS-485 on one reader port capable of supporting two readers). Two supervised inputs,
two relays. Diagnostic LEDs. Dedicated tamper input |
| Access Control | • 145,000 cardholder capacity, 50,000 transaction buffer. • 16 Access Levels per controller. • 8 digit PIN number maximum • Activation/Deactivation dates. • If/Then Macro capability |
| Card Formats | Eight active card formats per appliance — CAC, TWIC card compatible. Anti-passback support — Nested area, hard, soft, or timed forgiveness. |
| Alarm Management | Normally open/Normally closed, unsupervised, supervised. Standard or custom end-of-line resistances |
| Standards | UL294 Recognized, CE Compliant, RoHS, FCC Part 15 Class A, NIST Certified Encryption |
| ORDERING INFORMATION | |
| AC-MER-CONT-1DR | Access Platform EP1501 Single Door Controller with PoE Support (Mercury EP1501) |
Intelligent Two Door Controller
The Avigilon™ Access Control Manager (ACM)™ system supports open field hardware from Mercury Security allowing organizations to leverage investments in non-proprietary field hardware, with retrofit programs available for industry standard door hardware and card readers, including contact/contactless smart card, proximity, magnetic stripe and barcode.
The AC-MER-CONT-2DR is a powerful, intelligent controller solution for managing one or two on-board readers (expandable to 64 readers) with the Access Control Manager (ACM) system from Avigilon.
Based on the Mercury Security EP1502, the ACMER-CONT-2DR communicates with ACM via its on-board Ethernet port. The AC-MER-CONT-2DR includes eight inputs, four outputs and two reader ports and easily expands I/O and readers by simply adding input, output and reader interface modules. Offering powerful flexibility the AC-MER-CONT-2DR is capable of interfacing with a wide array of reader technologies for one or two controlled openings.
The Access Control Manager system and Mercury Security open field hardware provide the ultimate platform to complete the Avigilon end-to-end security solution.
KEY FEATURES
- RS-485 intelligent controller that supports a variety of independent
- functions
- Two-door interface with auxiliary I/O that expands to 64 doors
- Suitable for in/out reader applications
- Decentralizes system intelligence
- Network ready
- Provides full local processing
- Interfaces with a wide array of reader technologies including Wiegand, clock
- and data, magnetic stripe and keypads
- Onboard support for one or two controlled openings
- Support for up to 31 device addresses through the on board RS-485
- communication port
- Support for the AC-MER-CON-MR50, AC-MER-CON-MR52, AC-MER-CONMR16IN and the AC-MER-CON-MR16OUT
- Supports for the AC-MER-CON-MR51E over Ethernet
Specifications
| TECHNICAL SPECIFICATIONS | |
| Primary Power | 12-24 V DC +/- 10%, 500mA maximum |
| Serial Ports | Primary 10/100 Ethernet Port 2: RS-485, 2-wire |
| Reader Interface | Powered by PoE (12 V DC +/-10%) or local power supply (12 V DC). (PTC limited 150mA max) |
| Inputs | Eight general purpose: programmable circuit type Two dedicated: tamper and power monitor |
| Outputs | Four relays: Form C, 5A 30V DC |
| Reader Interface | Reader Power: 12 V DC ±10% regulated, current limited to 150 mA for each reader.(jumper selectable) or 12 to 24 V DC ±10% (input voltage passed through) current limited to 150 mA for each reader.
Data Inputs: TTL compatible inputs, mag stripe and Wiegand standards supported. Maximum cable length: 152 m (500 ft.). RS-485 Mode: 9,600 to 38,400 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and 1 stop bit. Maximum cable length: 609.6 m (2000 ft.).
LED Output: TTL levels, high>3 V, Low<0.5 V, 5 mA source/sink maximum.
Buzzer Output: TTL levels, high>3 V, Low<0.5 V, Low=Active, 5 mA source/sink maximum |
| Cable Requirements | Power: 1 twisted pair, 18 AWG. Ethernet: CAT-5, minimum. RS-485: (I/O Device Port): 24 AWG, 1,219 m (4,000 ft.) maximum, twisted pair(s) with an overall shield. (Reader Port): 24 AWG, 609.6 m (2,000 ft.) maximum, twisted pair(s) with an overall shield. RS-232: 24 AWG, 25 ft (7.6 m) maximum. Alarm Input: 1 twisted pair, 30 ohms maximum, typically 22 AWG @ 304.8 m (1000 ft.) |
| Dimensions (W x L x H) | 152mm x 203mm x 25mm; 6.0” x 8.0” x 1.0” |
| Temperature | Operating: 0° C to 77° C (32° F to 170° F) Storage: -55° C to 85° C (-67° F to 185° F) |
| Humidity | 10 – 95% Relative humidity (non-condensing) |
| Standards | UL294 Recognized, CE Compliant, RoHS, FCC Part 15 Class A, NIST Certified Encryption |
| TECHNICAL FEATURES | |
| Connectivity | Primary Port: 10/100 Ethernet |
| Door Control | Two reader ports: Mag or Wiegand Eight supervised inputs, four relays. Diagnostic LEDs |
| Access Control | • 145,000 cardholder capacity, 50,000 transaction buffer. • 16 Access Levels per controller. • 8 digit PIN number maximum • Activation/Deactivation dates. • If/Then Macro capability |
| Card Formats | Eight active card formats per appliance — CAC, TWIC card compatible. Anti-passback support — Nested area, hard, soft, or timed forgiveness. |
| Alarm Management | Normally open/Normally closed, unsupervised, supervised. Standard or custom end-of-line resistances |
| ORDERING INFORMATION | |
| AC-MER-CONT-2DR | Access Platform EP1502 Door Controller (Mercury EP1502) |
Single Reader Interface Module
Avigilon™ Access Control Manager supports open field hardware from Mercury Security allowing organizations to leverage investments in non-proprietary field hardware, with retrofit programs available for industry standard door hardware and card readers, including contact/contactless smart card, proximity, magnetic stripe and barcode.
The AC-MER-CON-MR50 is a low cost, high performance, single card reader, interface panel that is capable of all the I/O needed for managing a single (1) controlled opening with Avigilon’s Access Control Manager (ACM). Based on the Mercury Security (MR50), each AC-MER-CON-MR50 will interface one (1) card reader, two (2) generalpurpose input monitor points and two (2) control relays to provide access control andv security monitoring through the AC-MER-CONT-1DR, ACMER-CONT-2DR or the AC-MER-CONT-64DR intelligent controllers. The result is the flexibility, versatility and reliability required for demanding access control solutions. Access Control Manager and Mercury Security open field hardware provide the ultimate platform to complete the Avigilon endto-end security solution.
KEY FEATURES
- Compact footprint and RS-485 connectivity
- 12 or 24V DC input power support
- Interfaces with a wide array of reader technologies including Wiegand, clock
- and data, magnetic stripe and keypads
- Supports being clustered or distributed to best suit the installation
- environment
- Inputs and the output relays support assignment to door related functions or to
- general purpose I/O
- Inputs support normally open, normally closed, supervised and nonsupervised circuits
- Output relays are configurable for fail-safe or fail secure operation
Specifications
TECHNICAL SPECIFICATIONS
Primary Power
12-24 V DC +/- 10%, 150mA maximum
12V DC @ 110mA nominal
24V DC @ 60mA nominal
Communication
RS–485, 2-wire, 4,000’ (twisted pair with shield, Belden 9841)
Reader Port 1
Power: Input voltage pass-through Data Card/Keypad Clock/Data, Data–1/Data–0, or RS-485
LED
Two-wire, or one-wire bi-color LED support
Buzzer
Only with ‘one-wire’ LED
Inputs
2 General purpose: Programmable circuit type
1 Dedicated: Tamper
Output Relays
Relay 1: Form–C, 5 Amp 30 VDC
Relay 2: Form–C, 1 Amp 30 VDC
Dimensions
(W x L x H) 108mm x 70mm x 25mm; 4.25” x 2.75” x 1.0”
Temperature
Operating: -40° C to 75° C (-40° F to 167° F)
Storage: -55° C to 85° C (-67° F to 185° F)
Humidity
0 – 95% Relative humidity (non-condensing)
Standards
UL 294 Recognized, CE Compliant, RoHS
ORDERING INFORMATION
AC-MER-CON-MR50
Access Platform MR50 Single Card Reader Interface (Mercury MR50)
